Ultra-Compact Indoor/Outdoor
Background/Foreground Speaker
PLEASE NOTE: MINIMUM ORDER IS 2 UNITS.
MUST BE ORDERED IN MULTIPLES OF 2 UNITS: ( 2 4,6,8,10 etc.)
- 3" Woven-Fiberglass LF Drivers
- 0.5" PEI Diaphragm Tweeters
- 100W RMS at 8 Ohms
- 100W power handling of programmatic material in direct 8 Ohms setting, plus built-in multi-tap transformers 70/100volt operation
- Durable, Weatherized Enclosures
- InvisiBall Mounting Hardware
- Zinc-Plated Grilles
- Good for Off-Axis Listening
- 70 Hz to 20 kHz Frequency Response
Designed by JBL, these Control 23-1 loudspeakers
are two-way 3" indoor/outdoor monitors featuring weather-protected
circuitry, natural and powerful representations of the frequency
spectrum, black enclosures, and JBL's proprietary InvisiBall mounting
hardware. This hardware allows you to install the speakers through a
hidden access point behind its logo badge. As such, the Control 23-1
suitable for venues, health clubs, theme parks, cafes, or anywhere where
foreground/background music—and paging—is a necessity. These
monitors are capable of handling 100W of programmatic material at 8
Ohms, and feature a built-in multi-tap transformer for operation on
distributed speaker lines. With an SPL of 103 dB, you can blast these
speakers pretty loudly as well, while their cone geometry ensures a
pleasurable listening experience in both on- and off-axis situations.
Additionally, their PEI diaphragms render a smooth high-frequency
response. But sound is not the only consideration: Kapton voice coil
formers, JBL's WeatherEdge rubberized extensions, and a durable cabinet
construction provide protection against heat, rain, wind, or anything
else the elements might throw at you in the coming years. Also,
while the Control 23-1 comes in a black finish, it doesn't have to stay
that way: these speakers accept a variety of finishes and pigments to
match any surrounding. -
- 3" woofers with woven fiberglass cone
- 0.5" PEI diaphragm tweeters with fluid cooling
- Built-in InvisiBall mounting hardware
- Weather-resistant enclosure and transducers
- 100° x 100° coverage
- 100W power handling of programmatic material in direct 8 Ohms setting, plus built-in multi-tap transformers
- Frequency response of 70 Hz to 20 kHz.
|
|
Power Rating
|
100 W continuous program (2 h)
50 W (200 W peak), continuous pink noise (2 h)
40 W (160 W peak) continuous pink noise (100 h)
|
|
Nominal Impedance
|
8 ohms (THRU setting)
|
|
Maximum Input Voltage
|
17.2 V RMS (2 h), 34.4 V peak
|
|
Frequency Response ± 3dB
|
95 Hz to 19 kHz
|
|
Frequency Response ±10 dB
|
70 Hz to 20 kHz
|
|
Sensitivity
|
86 dB, 1 W / 1 m (average 100 Hz to 10 k Hz)
|
|
Coverage Angle
|
100° x 100°
|
|
Directivity Factor
|
5.8 (averaged 1 kHz to 16 kHz)
|
|
Directivity Index
|
7.2 dB (averaged 1 kHz to 16 kHz)
|
|
Crossover Type
|
2nd order low-pass, 2nd order high-pass
|
|
Transformer Taps
|
70 V: 15 W, 7.5 W, 3.7 W, 1.8 W
100 V: 15 W, 7.5 W, 3.7 W
Insertion loss < 0.43 dB at any tap setting
Thru setting: 8 Ohms nominal
|
|
Recommended Protective High-Pass
|
70 Hz high-pass (24 dB/oct) (for 8 Ohms operation and for all 70 V / 100 V taps settings)
|
|
LF Driver Size
|
3" / 76 mm
|
|
HF Driver Size
|
0.5" / 13 mm
|
|
Driver Type
|
LF Driver: Woven-fiberglass cone with pure butyl rubber surround
with Weather-Edge frame protection, high-temp Kapton voice coil former,
high-temp voice coil wire, optimized cone geometry, linear suspension
spider, and FEA optimized motor structure
HF Driver: PEI diaphragm, low-viscosity ferro-magnetic fluid, and Kapton voice coil former
|
|
Enclosure Material
|
High-impact polystyrene (HIPS)
|
|
Grille
|
Highly zinc-plated, finished in durable TGIC polyester powder-coating
|
|
Termination
|
Screw-down terminal strip, zinc-plated copper based,
nickel-plated metal screws and washers. Accepts up to 9 mm outside 4 mm
inside open lugs (#6, #8, or #10 lug), plus bare wire (up to 12 AWG /
2.5 mm2)
|
|
Environmental
|
IP-44 per IEC529; exceeds MilSpec 810 for humidity, salt-spray,
temperature & UV; passes MilStd-202F for salt spray and ASTM G85 for
acid-air plus salt spray
|
|
Agency Rating
|
ROHS-compliant; Transformer UL Recognized per UL1876
|
|
Dimensions (H x W x D)
|
7.9 x 5.6 x 4.4" / 200 x 141 x 111 mm
|
|
Weight
|
4 lb / 1.8 kg
|
800-834-5986
